m5svv1-1 repair

Diskutiere m5svv1-1 repair im English Section Forum im Bereich *** Allgemein***; Thanks for your reply. According to my measurements at the LM2940 - when switched on cold - it measures 8.9V at the input and 4.5V at the output...
  • m5svv1-1 repair Beitrag #21
B
bgcanib1
Teetrinker
Dabei seit
01.11.2016
Beiträge
8
Thanks for your reply.
According to my measurements at the LM2940 - when switched on cold - it measures 8.9V at the input and 4.5V at the output. When normal operating (same as switched on hot) it's 12.5V at the input and 4.75V at the output. It seems that something squeeze high power at the low voltage level when the machine is cold and after some time it gets back to normal. I've measured the capacitors, they seems to be good but I will double check. According to your diagram are the D1 and D13 zener diodes 5.6V and 4.7V respectively?
 
  • m5svv1-1 repair Beitrag #22
hmilbradt
hmilbradt
Super-Mod
Dabei seit
03.01.2005
Beiträge
27.150
According to your diagram are the D1 and D13 zener diodes 5.6V and 4.7V respectively?

Yes they are.. But D13 actually is not involved with the 5 VDC power supply. This part of the circuit creates a 100 Hz Zero-Voltage-Crossing signal of the mains sinus curve. The microprocessor uses it to fire the triacs at the correct time. D1 limits the max. output voltage auf the power supply. Its an additional safety feature.
By the way. The thread was opened wtth problems of a M5SVV1-1 PCB. Does your machine use this PCB ??
 
  • m5svv1-1 repair Beitrag #23
B
bgcanib1
Teetrinker
Dabei seit
01.11.2016
Beiträge
8
Actually my power board is M5DPWRV15 and the CPU board is M5DCPUV16 , but since only this section is in English and I didn't find any other treads about these I've posted here. If it's not the right place please tell me where I can look for support. Anyways I continue to struggle with this issue. There is something wrong in the power supply or something else, I have unplugged the cable between the 2 boards and when the machine is turned on there is the dozer magnet coil and the relay that turn on permanently.
 
  • m5svv1-1 repair Beitrag #25
B
bgcanib1
Teetrinker
Dabei seit
01.11.2016
Beiträge
8
Thanks a lot for your support, hope to find the short circuit soon. I will post the results...
 
  • m5svv1-1 repair Beitrag #26
B
bgcanib1
Teetrinker
Dabei seit
01.11.2016
Beiträge
8
Hurrah! I did it!

There was a bad capacitor C1-470 uF at the power supply circuit. After changing it works great now. Thanks for the links, this forum is great.

Best,
Ivo
 
  • m5svv1-1 repair Beitrag #27
hmilbradt
hmilbradt
Super-Mod
Dabei seit
03.01.2005
Beiträge
27.150
Thank you for the feedback.

Harry
 
  • m5svv1-1 repair Beitrag #28
T
TonyP
Teetrinker
Dabei seit
04.09.2016
Beiträge
13
I finally got around to soldering a new microprocessor onto my M5SVV1-1 board after it arced over. I am happy to say that it was successful and I am now enjoying fresh coffee from my old machine again.

I bought a used Saeco Magic Comfort to get me by while my Vienna was broken, and I have noticed that the Magic heats up much more quickly (50 seconds from off overnight, ambient room temperature 20°C vs the Vienna 2 mins 5 seconds).

Would anyone with a Vienna twin boiler be able to time their machine on startup, or is anyone able to tell me if this is normal?

I descaled the machine and this didn't help the warmup time, besides we have very soft water here.

Thanks, Tony.
 
  • m5svv1-1 repair Beitrag #30
T
TonyP
Teetrinker
Dabei seit
04.09.2016
Beiträge
13
Thank you Grisu. The Magic Comfort is 1250 watts and one boiler, the Vienna is also 1250 watts but 2 boilers, naturally will take twice as long to warm up.
 
  • m5svv1-1 repair Beitrag #31
V
ValeriyP
Teetrinker
Dabei seit
15.10.2019
Beiträge
14
Hello. Problem with Spidem Trevi Exclusive. When turned on, the motor jerks and the error indicator flashes. At 7805 comes 12V comes out 4.97V. In testing mode, all functions work out. When during testing, the portion size control is in the middle and maximum position, the error indicator blinks, while in the minimum position the error does not blink. Kontseviki checked. What could be the problem?
 
  • m5svv1-1 repair Beitrag #32
Grisu
Grisu
Moderator
Teammitglied
Dabei seit
18.03.2009
Beiträge
12.419
Ort
Wien
Vollautomat
Incanto SUP021Y u. YBDR, Krups Orchestro
@ValeriyP Please open your own new thread in ..:: Saeco Klone ::..
Spidem Trevi Exclusive is similar to Seaco Vienna, maybe this can help you in further investigation. And translate "Kontseviki". If you use a translator (like google) use German, if you write in English on your own stay with it for better understanding.
 
Thema:

m5svv1-1 repair

ANGEBOTE & SPONSOREN
Wunderkessel.de - Die Koch-Community mit Herz
Oben