Saeco Incanto de Luxe - No Water

[Nusik1975]

Guten Tag. Ist aus anderem Thema übergegangen.
Es gibt den Wagen Saeco Incanto de Luxe SUP021YBDR. Bei dem Einschluss geschieht die Diagnostik zuerst. Es sind die Nasenstüber des Motors und des Mechanismus hörbar. Später erscheint auf dem Display die Aufschrift - es Gibt kein Wasser. Ist ins Servicemenü eingegangen. Die Pumpe arbeitet, hat geprüft. Ротаметр mit dem Sensor der Halle arbeitet auch, hat geprüft. Pumpen neben 0,5 Liter des Wassers mit Hilfe der Pumpe. Die Pumpe ist intakt. Kann, es gibt den Sensor der Auffüllung zu Wasser irgendwo?
Ich bitte, mich für schlecht deutsch, mich selbst aus Russland zu entschuldigen. Ich benutze das Wörterbuch.
Wenn es klarer sein wird, werde ich auf der englischen Sprache noch schreiben.
Ich danke Sie für die Antwort!

 

[Nusik1975]

Hello! There is coffee-machine Saeco Incanto De Luxe SUP021YBDR. At switching-on at first there is diagnostics, engine noise is audible. Then the inscription on the display - Isn't present some water. By means of the service menu has checked up the pump - water swings. Has checked up ротаметр, it is serviceable, pulses are. Perhaps where there is still a sensor on water presence? I thank you for the answer.

 

[Grisu]

is this correct: water comes through but machine doesnt recognize it?

machine recognize "no water" going through because flowmeter is possibly not working correct.

from the tank the water goes first to this flowmeter on the bottom of the machine the white thing.

you can put it out and open it, oftne there is something blocking it so it cant turn round.
clean it and try again, magnetic part of the turbine must be upside. remember the direction of the water flowing through the flowmeter! check that it is connectet on the main-board.

 

[Nusik1975]

So that's just the point that at start diagnostics the pump doesn't turn on. And accordingly, the turbine too to be twisted in any way without the pump won't be.

 

[Nusik1975]

I have checked up this flow meter. It works. And to a board too it is connected. Whether the pump should turn on for some time at machine switching-on in a network?

 

[Grisu]

Have you been in test-mode, does there water come?
do you have hot water or steam?
does the magnetic swimmer go up in the tank or is he sinking to the bottom?
if you blow through the water input whole does the flowmeter turn (you can hear it turning silent and is it turnig some time longer after stopping to blow), open hotwater wheel for this part that the air can go out.

 

[Grisu]

pump starts only if it has been in standby longer time, to clean the machine, otherwise it doesnt pump when switching on. in test-mode you can check only the pump (use the link to test-mode!).
you can even put 230V directly on the pump pins to check if it is working.
Do this ONLY if you do know electrical fundamentals!!!

 

[Nusik1975]

Here fur-trees-sticks!
In the same place the sensor is on a back wall. And at me shortage, the device has got from relatives. There there is no at me a magnetic float. I will try to deliver a constant magnet there. I thank you for the help!!!

 

[Nusik1975]

Has checked up under the drawing. I in a tank for water don't have positions #4 and #5. It is a float with a magnet and a cover of a bay for a float. I will invent something. To buy such things from us it is unreal and if to order through an e-commerce shop it will be very expensive. Tomorrow I will try and I will unsubscribe here.

 

[Grisu]

you could short the pins of the reed-sensor-switch. then the machine allways thinks there is enough water in the tank. But you have allways be sure that there really is enough water, otherwise the pump takes air and can be damaged! or place a little magnet near the sensor on the backside.

 

[Nusik1975]

wehe,
I thank you for the help, all works! It was not simple a magnetic float! Thanks you and a forum!